Bulldog Winch Receiver Mount Kit - 2" x 2"
(71 reviews)
Price: $98.00
In Stock
Bulldog Winch Receiver Mount Kit - 2" x 2"
Retail:$128.71
Our Price: $98.00
You Save: 24%
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Customers prefer these similar products
34% prefer this
- All Info
- Reviews (71)
- Q & A (0)
- Videos (1)
- Photos
Bulldog Winch Accessories and Parts
- Electric Winch
- Mounting Hardware
- Plates
- Bulldog Winch
- With Handle
- 2" x 2" Receiver mount fits your budget with bolt-together design
- Adjustable handle positions
- Used for truck winches up to 12K with 10 x 4.5" mounting bolt patterns
- Will not fit large body truck winches or Alpha Series
- Capacity is based on capacity of vehicle receiver
20155 Bulldog Winch Receiver Mount Kit - 2" x 2"
Item # BDW20155
California residents: click here
Video of Bulldog Winch Receiver Mount Kit - 2" x 2"
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Video Transcript for Bulldog Winch Electric Winch BDW20155 Review
Speaker 1: Today, we're gonna take a look at the Bulldog winch hitch receiver mounting plate for 2" hitches. Now this will offer a portable mounting option for your winch. Your winch will basically mount onto this mounting plater, has the adjustable handle positions right here, make it very easy to transport your winch from different vehicles. It is designed to fit into any standard 2" by 2" hitch receiver. They do even include the hitch pin and clip to install it into your hitch receiver. Now this is used for truck winches up to 12,000 pound capacity that uses a standard 10 and 4 1/2" mounting bolt pattern.
You can see the bolt pattern they have on the mounting plate. Now one last note. The capacity on this is based on the capacity of your vehicle receiver and this also will not fit large body truck winches because those winches are too heavy for portable use, too large to fit onto this plate and it will not fit the alpha series because the frames on the alpha winches are too large to fit into this mount.You can see they do have the three different holes at the bottom so you can put the bolt through there just to adjust whatever position you need these handles in. But again, you just have your winch mounted on here. You can grab it by the handle, slide it into the hitch receiver and then when you're done, you can just pull it right out.
But that should do it for the review on the Bulldog winch hitch receiver mounting plate for 2" hitches.
Customer Satisfaction Score:
98% were satisfied with this product
2% of customers were not satisfied
- Defective
- Wrong item was ordered
Customer Reviews
Bulldog Winch Receiver Mount Kit - 2" x 2" - BDW20155
Average Customer Rating: 4.8 out of 5 stars (71 Customer Reviews)
by: John04/17/2024
I'm off to overland in Texas and wanted you to know that the hitch and winch carrier are perfect. Using quick connectors, I can use ir on the front and rear.
Removing it also saves on gas.
It works great with a moulded number, saving on buying a specialized steel bumper and other expensive attachments.
I like that I can still have all the internal mud guards and brush cover without having to take them off and not be able to have them on.
Awesome!
by: Wade03/30/2022
The overall build and construction of the mount is actually quite good, I have no complaints there. It seems to be made well and is as advertised. Unfortunately, however, that’s the only good news: not only did the package arrive almost completely destroyed but because of this several pieces of hardware were missing. Still, I was willing to overlook this as it could’ve been partially the fault of FedEx/ UPS. The reason that I am only giving it 1 star is because, contrary to the answer given in the Q&A, this mount DOES NOT fit my Warn Zeon 12-S winch. The reply when asked about fitment was “Yes, the Bulldog Winch Receiver Mount Kit part # BDW20155 will work with the Warn Zeon 12-S Platinum Winch 95960 as they both use the same industry standard 10" long x 4-1/2" wide mounting pattern.” As long as you are willing to do without the handles this answer is true. Misleading, but true. It may be worth noting that as long as you have a winch that is smaller in overall size than the Warn Zeon 12-S, it should work just fine.
by: David B 03/20/2019
Product arrived on time packaged well no damages because of my setup I have to get a extension to clear my current brush guard however was all put together when came out of the box but 4 bolts for the handles super easy to use holds my smittybilt 12k winch perfectly and fits nice in the receiver without a lot of wiggle very good product
Mike L.
3/21/2019
Keep in mind that using an extension will lower the capacity of the hitch to a degree, because of the extra leverage exerted especially if the winch is pulling at an angle. If the extension were to break under load, it could lead to injury.
by: Trevor01/06/2022
I picked this winch from etrailer as it provided an incredible value at the time of purchase vs other option here and from other retailers. It ended up being way overkill for what I use it for, but I never have to worry about overloading it either. Went together well and mounted up like it should to the Bulldog receiver mount I got too (hitch plate welded/mounted on car hauler, winch is removable and not subject to road grim ever). Plan on years of service from this combination!
by: William10/02/2018
Quick service…. looks sturdy, maybe a little iffy for 12,000 pound winch. A snatch block will fix that load issue. The paint is already peeling on the corners. I previously ordered a Curtis Front tire carrier, different vender , however it will NOT fit a Dually TIRE. so planning on placing a spare tire on the platform and securing with ratchet straps.
by: Thomas11/17/2018
Good concept, but extremely flimsy, as it relies only on the hitch receiver for stability. It definitely needs some additional parts to keep it from wiggling, bending and rocking when the winch (SmittyBuilt) is in use. I doubt that it could even pull my little Ridgeline out of a ditch without deforming or ripping apart, but I'm afraid to test it.
by: Gino05/24/2021
Came as described, packaging was beat up pretty bad but nothing wrong with the plate. Holds my Badlands winch no problem, this is a better solution to needing a winch other than spending [money] on a front bumper with a winch mount.
by: Lance 11/05/2021
As usual, another great experience with etrailer. Shipped super quick. Love the handles, which are a must-have if you will be hitch mounting and dismounting a heavy portable winch a lot. Handles are also adjustable so allow for a lot of different winch sizes.
by: Wade 07/21/2023
Fast delivery! Looks Great!
by: Tmc05/23/2019
This fit my Badland 12k winch very well, it's very heavy duty and I don't worry about the ability to handle what I throw at it, not to forget the price was very reasonable thanks etrailer.
by: Jack10/13/2017
This cradle is light and compact and looks pretty sturdy. Since tow receivers are only rated for 5000# and my winch is rated for 9000#, I will run my winch cable through a snatch block and back to a hook on my tow receiver.
by: Carl05/31/2020
Easy setup for my winch and it makes it easy to get mounted to my trailer hitch. A great product if you want to have a winch but don’t want a permanent mount.
by: Bob 01/28/2021
The Bulldog Winch Receiver is a must-have. Fit my needs perfectly. Easy to use and makes using the Bulldog winch that much easier.
by: Jimmy04/14/2019
Working great with my 12000lb winch. thanks. works with my truck and car hauler
by: Gary 05/18/2020
Very well made! Strong and stout, Don get the cheep one fellas, you or someone else may be depending on it. Haven't gotten my winch yet but when I do I will post pictures.
As always, a great experience working with and purchasing from etrailer!
by: Rick03/23/2020
Well Built. Much more substantial handles compared to the bent tubing on others. Love how the handles are adjustable to fit the winch. Easy to use.
by: Deborah 10/22/2022
Nice and strong. Just a bit too tight for our warn 8000 winch. Tight squeeze, but made it work aok!
by: vic06/25/2018
Not too impressed. It seems pretty lightweight for a winch carrier. In all fairness I have not used it yet but that is my first impression
by: butch04/30/2017
very happy with the winch and mount, instructions were easily understood and the finished product was all it was said to be. will continue to deal with this business as they are professionals.
by: Bill 12/20/2020
Winch receiver mount is well made and works great with the Badland Apex winch.
by: Tim L.06/18/2016
Totally pleased with mount.
Much better quality than I thought I would get for the price !!
Putting a 12,000 lbs winch on it, not worried about the mount at all.
Once again etrailer delivers !!!
by: Rick12/26/2018
Well Built, Real Decent Quality, And Easy Installation. A #1.
by: Terry06/02/2018
great price, fast shipping. exactly as described. have purchased many items from etrailer and always satisfied.
by: Jesse B01/09/2021
Came in 2 days after I placed my order. Packaged well and everything as it was advertised! Appears to be quality winch cradle at a great price.
25
71
Show More Reviews
See what our Experts say about this Bulldog Winch Accessories and Parts
- Front Mount Trailer Hitch Receiver For 2011 Ford F-350 Extraction WinchYour 2011 Ford F-350 with a GVWR of 10,800lbs is the maximum amount the vehicle can weigh fully loaded. Depending on your configuration your curb weight is likely between 6,000-7,500lbs. Since you plan on using for a winch and mud will be involved I recommend the EcoHitch Hidden Front Mount Trailer Hitch Receiver # EH59FR. It has a maximum line pull rating of 10,000lbs. By using the Bulldog Winch Receiver Mount Kit # BDW20155 you will have the capability to move the winch to either...
view full answer... - How To Mount a Winch On the Front of a 2007 Hummer H3I do have a winch mounting option for a 2007 Hummer H3 but it requires a front mount trailer hitch and hitch mounted winch tray like the Curt Front Mount Trailer Hitch Receiver part # 31270 and Bulldog Winch Receiver Mount Kit part # BDW20155 or you could go with the ComeUp Off-Road Winch w/ Mounting Plate for 2" Hitches part # CU854768.
view full answer... - Can Front Receiver be Installed on 2015 Jeep Wrangler Unlimited w/Base Plates Already InstalledThe base plates and front mount hitches (which you would use to mount a winch) install at the same places on the frame of the 2015 Jeep Wrangler Unlimited so you cannot have both at the same time. I recommend putting a winch at the back of the Jeep. For a 2 inch trailer hitch you can use the Bulldog Winch receiver mount # BDW20155 . Then you can attach a Superwinch electric winch. I have linked the Superwinch models for you.
view full answer... - Recommended Hitch Receiver Mount For Superwinch UT3000The receiver mount compatible with your Superwinch UT3000 is the Bulldog Winch Receiver # BDW20155 with handles for ease of installation or # BDW20061R2 without the handles. I can easily recommend either option so it all depends on your personal preference for appearance and function. I've attached a couple videos to assist you in your decision.
view full answer... - Front Mount Trailer Hitch and Winch Mount for a 2005 Ford ExcursionThere are front mount hitches available for your 2005 Ford Excursion but TorkLift hitch # TLF1006 will not fit. The available front hitches that do fit are Draw-Tite hitch # 65022 and Curt hitch # 31114. Both are rated for 9,000 pounds line pull and 500 pounds vertical load. For a winch mount that fits in a 2-inch receiver we have: # C31010 # BDW20011 # BDW20155
view full answer... - Front Hitch and Mount Recommendation for 2016 Ford F-450For a front hitch confirmed as a fit for your 2016 Ford F-450 we have the Draw Tite part # 65049 which will work great as a way to mount your front hitch. Once installed the winch mount part # BDW20155 that you referenced would fit and work well to carry a Bulldog Winch like the 12k Standard Series # BDW10043.
view full answer... - Winch Mount Compatible with Kubota RTV900 with 5000 lb WinchThe Bulldog Winch Receiver Mount Kit - 2" x 2" # BDW20155 is a fit for any 2 inch receiver, so if you have a 2 inch receiver on your Kubota that can handle the line pull of your winch, you will be fine. We also have a custom Kubota RTV mount for your RTV900. You may be interested in the Bulldog Winch Custom-Fit Steel Winch Mount # BDW15172.
view full answer... - Parts Needed to Install 9,000 lbs Winch on the Front of a 2008 Jeep Liberty Aside from using the Curt Front Mount Trailer Hitch Receiver # C31020 to mount a winch on your 2008 Jeep Liberty there are a few other things that you will need to use Once the front trailer hitch is installed you can then use the Bulldog Winch Receiver Mount Kit # BDW20155 to carry the Bulldog DC9.0 Integrated Off-Road Winch # BD500600 which is rated for 9,000 lbs and is compatible with the mounting bracket kit. This winch comes with a remote control so that you can monitor the your...
view full answer... - Will the Bulldog Winch Receiver Mount Kit Work With a Ramsey RE1200 WinchThe Bulldog Winch Receiver Mount Kit part # BDW20155 has an industry standard mounting pattern (10" x 4.5") which all winches up to 12,000 lbs share so yes it will work with a Ramsey RE1200 Winch.
view full answer... - Comparing Curt and Draw-Tite Front Mount Hitch Receivers For a Winch on a 2015 Ford F-150 XLTThe Curt Front Mount Trailer Hitch Receiver # C31083 and Draw-Tite Front Mount Trailer Hitch Receiver # 65067 are currently the only 2 front mount receivers that are custom fit for your 2015 Ford F-150 XLT. Both receiver have the same 9,000lb line pull rating for using your winch and both will support a tongue weight of up to 500lbs which will allow you to use it for other things during the summer. Visually both receivers appear the same and have very similar construction. If you plan...
view full answer... - Availability of Front Receiver for 2017 Jeep Wrangler that Attaches to Outside of Frame RailsUnfortunately, the front receivers offered for the 2017 Wrangler JK fit to the inside of the frame rails, we don't offer one that installs in any other manner. One option that would allow you to use both the winch and the front mounted receiver would be to use a receiver winch mount like # BDW20155. If you went this route, you could temporarily disconnect the winch when the receiver is needed for other purposes by using a quick disconnect on the wiring. I've linked to the quick disconnects...
view full answer... - Mounting Options for Bulldog Winch on 2018 Ford F-150To mount the Bulldog Winch # BDW10041 to your 2018 Ford F-150 I recommend using the Westin MAX Winch Mounting Tray # 46-23835. This is a custom rust-resistant steel tray that will bolt to your truck's frame to accommodate the Bulldog Winch with pre-drilled mounting holes. All of the hardware is included. I have attached the written installation instructions that you can also check out. Another, less permanent solution is with the Bulldog Winch Receiver Mount Kit # BDW20155 that will...
view full answer... - Warn Zeon 8 Winch Confirmed Fit with Bulldog Winch Receiver Mount KitThe Bulldog Winch Receiver Mount Kit - 2" x 2" # BDW20155 is a fit for any winch up to 12K with 10 x 4.5 inch mounting bolt patterns. I was able to find the Warn Zeon 8 online and it does have this same mounting pattern so it is confirmed to fit the Bulldog mount.
view full answer... - Front Hitch and Winch Plate for 2017 Ford F-250 for Mounting Winch at Front of TruckYour biggest issue is going to be that the grille guards and the front hitches occupy the same area and use the same install points on the frame of the vehicle so there's no easy way (if at all) to install both at the same time. If you aren't super attached to the grille guard idea I'd go with just a front hitch so you could use a removable winch plate like the # BDW20155 at both the front and the rear of the vehicle. The Curt Front Mount Trailer Hitch # C31078 that you referenced is...
view full answer... - Can an Electric Winch be Used on a 1987 Kawasaki KLF 300 Bayou 2x4There is not a custom winch mount for your model ATV, however if you have a 2 inch trailer hitch receiver like # C45006, you could use a Winch Receiver Mount like # BDW20155. With a mount combination like this, you could absolutely use an electric winch. My recommendation is the Bulldog Winch Powersports Series ATV Winch # BDW15014 which will work very well for your application and give you easy to use controls at your handlebars. I've attached a video to assist and you can see the prices...
view full answer... - Hitch Mount Recommendation that Fits 12k Bulldog Winch # BDW10039Yes, the Bulldog Winch Mount part # BDW10039 does work with the Bulldog Winch part # BDW20155 that you also referenced. The mount fits winches with up to a 12k capacity and mounting dimensions of 10" by 4-1/2" which is exactly what the winch you mentioned has.
view full answer... - Recommended Winch Mount For 2000 Dodge Ram 3500 Turbo DieselThe Winch Carrier for Bulldog Winch Grille Guard - 12,000 lbs # BDW733601 is not a fit for your 2000 Ram 3500. The only mount that is available is a receiver mount like the Bulldog Winch Receiver Mount Kit - 2" x 2" # BDW20155 or the Curt Trailer Hitch Electric Winch Mount Plate # C31010. For this you will need a front mount receiver if you don't already have one. We have the Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2" # 31604 which is a great option for you, and it is...
view full answer... - Front Mount Hitch Recommendation for Adding Winch to 2021 Toyota TacomaI recommend going with the Curt Front Mount Trailer Hitch Receiver # C31075 for your 2021 Toyota Tacoma because it will be easier to install and has the same line pull rating as the Draw-Tite # 65070. The only reason I would recommend the Draw-Tite over the Curt is if you are going to be pushing that 350 lb vertical load limit, but even then you'll need to ensure that your truck has that high of a weight rating in the front. I've attached a photo of the Curt hitch installed on a Tacoma...
view full answer...
- Will the Superwinch S9000 Work on a Mounting Plate at the Rear Hitch Receiver of a 2012 Dodge RamThe Superwinch S9000 Heavy Duty Recovery Winch is confirmed to work with the Hitch Mounted Winch Mounting Plate # BDW20155. In order to install the winch at the rear of your vehicle you will also need to install a wiring kit like # BDW20206 because the wiring located at your bumper is not nearly adequate for the amperage draw of a winch. This will also give you quick connect terminals to make installing and removing the winch easy.
view full answer... - How Can a Westin Grill Guard and Winch Be Install On 2005 Dodge Ram Pickup?I have an option to get your truck setup with a grill guard and winch, but Westin does not make a Grill guard for your 2005 Dodge Ram that has a winch mount, so there's no hardware available to mount a guard of that style to your truck. Your only option for a grill guard is going to be the Westin # 40-1205 in black or # 45-1200 in chrome. These will fit no matter if your truck is a 1500/2500/3500, and are custom designed just for your truck. To add a winch you'd need to add a front mount...
view full answer... - Highest Weight Capacity for Front-Mounted Hitch on 2018 Ford F-350 Super DutyThere are a pair of front-mounted hitches that fit your 2018 Ford F-350 and both, the Draw-Tite # 65076 and Curt # C31078, have a weight capacity of 9,000 lbs and though I cannot tell you with absolute certainty a 12,000 lb front-mounted hitch does not exist, 9,000 lbs is generally what you are going to see. There are winch mounts that fit in a receiver such as the Bulldog Winch Receiver Mount Kit # BDW20155 which are for 12,000 lb winches but you would be limited to the 9,000 lb capacity...
view full answer... - How To Use Front Mount Hitch and Bull Bar Together on a 2012 Toyota Tacoma 4x4The best fit front mount trailer hitch we have for your 2012 Toyota Tacoma 4x4 is the Draw-Tite Front Mount Trailer Hitch Receiver part # 65070. The reason that this is the best fit trailer hitch is because it allows you to retain the skid shield unlike the Curt Front Mount Trailer Hitch Receiver part # 31313. Unfortunately, you will most likely need to remove your bull bar as it will mount in the same location as either front mount hitch. This is the case for most vehicles though so it's...
view full answer...
- Bulldog Winch and Mounting Bracket For a 2019 Toyota 4Runner I have a couple options for you as the Bulldog Winch Off-Road Winch Mounting Plate for Toyota Tacoma Gen III # BDW23001 is only confirmed to fit the Gen 3 Tacoma and they do not have a separate plate for your 2019 Toyota 4Runner. First you can have a custom mounting plate created using the Universal Mounting Plate # BDW20291. This will need to be completed at a fabrication facility near you. Or you can use the Bulldog Winch Receiver Mount Kit # BDW20155 with a front mount receiver....
view full answer... - Hitch Mount for Front Hitch to Use with Winch Powerplant and CompressorWhile we don't carry the Winch Powerplant that has the air compressor built in we do know that it is designed to fit on standard winch mounts so the Bulldog Winch Receiver Mount Kit # BDW20155 that you referenced would fit and work great. The handles of it also make it really easy to install and remove from the hitch too. I attached a review video for this for you to check out as well.
view full answer...
Do you have a question about this Accessories and Part?
Info for this part was:
Edited by:
Tyler C
Installed by:
Jeff D
Expert Research:
Jameson C
Expert Research:
Adam R
Written by:
Lisa S
Updated by:
Matthew S
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Jenny N.
4/7/2022
I will have our Customer Service team reach out to you. I have reached out to the manufacturer and confirmed that this mounting plate does prevent clearance for the handles on the Zeon winch. There is another winch plate that would work as it is designed for oversize frame winches up to 12k. It is part # BDW20011.